Pipe Repair in Crane, TX — All Pipe Materials, Same-Visit Repairs
In Crane's mixed housing stock, a single repair call might involve copper sweated joints, threaded galvanized fittings, push-connect PEX transitions, or CPVC drain arms — sometimes all in the same house. Our techs carry the materials and know the techniques for every pipe type commonly found in TX homes.
How Masters Plumbing Service Approaches Pipe Repair in Crane
Our techs work on every pipe material found in Crane, TX homes, from pre-1970s galvanized to modern PEX-A crosslinked systems. The repair method matches the pipe.
🔊
Acoustic Leak Detection
Pressurized water escaping a pipe creates a characteristic acoustic signature. Our listening devices amplify ground and structure-borne sound to pinpoint a leak location within inches — through concrete slabs, behind drywall, or under flooring. This means we open only the section of wall, floor, or slab directly over the failure.
🌡️
Thermal Camera Scanning
Active water leaks create temperature differentials on wall and floor surfaces detectable with an infrared camera. A slow leak inside a wall shows as a cold, spreading zone; a hot water line leak shows the inverse. Thermal imaging confirms leak presence and approximate location before any cutting begins.
🛠️
All Pipe Materials & Joining Methods
Our techs are proficient in copper sweating (soldering), press-fit connections (ProPress system), CPVC solvent welding, PEX crimp and expansion fitting installation, threaded galvanized repair, and ABS/PVC drain line work. We match the repair method and material to the existing pipe system rather than forcing incompatible transitions.
🔒
Pressure-Tested Before We Leave
Every supply line repair is pressure-tested before we close the wall or floor. We pressurize the repaired section, hold the test pressure for the required duration, and confirm zero drop before considering the repair complete. You don't find out there's a second leak next week — we find it before we pack up.
Our Pipe Repair Services
What We Fix — Pipe by Pipe, Material by Material
From a pinhole copper leak behind a kitchen cabinet to a full galvanized repiping, our pipe crew in Crane, TX handles the full range.
Copper
Copper Pipe Repair & Repipe
Pitting corrosion in copper is sometimes systemic rather than localized — a single pinhole is often the first of several to appear. When the camera or pressure test finds multiple deteriorated sections, we give you an honest assessment of whether targeted repair or full copper repipe is the better long-term answer.
Galvanized
Galvanized Pipe Replacement
We replace galvanized supply lines with copper or PEX — either as targeted section replacement at active failure points or as a full-house repipe project. We connect the new material to existing fittings using dielectric unions where code requires to prevent galvanic corrosion at copper-to-galvanized transitions.
PEX
PEX Pipe Repair & Extension
PEX is also the material of choice for extending or reconfiguring supply runs during remodel work. Its flexibility reduces fitting count and eliminates the need for torch work inside walls.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
A burst pipe from freezing or sudden pressure surge requires immediate water shutoff and precise repair. We locate the failure, determine whether it's a single failure point or multiple freeze-damaged sections, and repair with a method appropriate to the pipe material — press-fit coupling for copper, expansion coupling for PEX-A, or a mechanical repair coupling for emergency situations.
Slab Leaks
Under-Slab Pipe Leak Repair
Slab leak rerouting is often more cost-effective than direct access, particularly for longer runs or under tiled floors. We present the options honestly with pricing so you can choose based on your priorities.
Full Repipe
Whole-House Repipe Service
A full repipe in Crane typically completes in 2–3 days for a standard single-family home. You're without water for a portion of each day; we plan the schedule to minimize disruption to occupied rooms.
We don't open walls at random. Acoustic and thermal detection tools tell us exactly where to cut before we pick up a saw.
1
Call & Describe — We Shut the Water If Needed
For emergency burst pipe calls, we dispatch immediately. For suspected slow leaks, we schedule at the earliest available slot and confirm before arrival.
2
Pressure Test & Acoustic / Thermal Detection
We pressurize the supply system and monitor for pressure drop to confirm an active leak. Then acoustic listening devices and the thermal camera locate the failure to within a small area — telling us which section of wall, floor, or slab to open.
3
Flat-Rate Quote & Minimal Access Opening
You receive a flat-rate quote covering the specific repair based on what the detection confirmed. We open only what needs to be opened — typically a 12–18 inch drywall or flooring access, not a full wall section.
4
Repair & Pressure Test — Then You're Done
You receive a written summary of what failed, what we installed, and the warranty terms before we leave.
Customer Reviews
Real Pipe Repair Reviews from Crane, TX Homeowners
★★★★★
My older home had a copper supply line fail inside an exterior wall. The thermal camera showed the wet zone through the drywall without any cutting. They opened a 10-inch section right at the pinhole, put in a press-fit repair coupling — no torch in my wall — pressure tested, and patched the drywall themselves. Two hours total.
— N. Bergman, Crane
★★★★★
Had an under-slab leak diagnosed by Masters Plumbing Service with acoustic equipment. They found the leak at 6 feet from the wall — a single copper elbow that had developed a pinhole. Presented three options: direct slab access, reroute through the wall framing above, or copper lining. I chose the reroute — they ran a new PEX line through the crawl space and connected at both ends without touching the slab. Pressure tested, verified no remaining drop. No jackhammering at all.
— O. & R. Adeyemi, Crane, TX
★★★★★
I noticed my water meter spinning with all fixtures off — confirmed a leak in the supply system. Masters Plumbing Service ran a pressure test and acoustic scan, found a pinhole in a copper section under the slab in the utility room. They rerouted the line through the wall above slab, tested, and closed out the permit. The reroute was exactly the same cost as direct slab access would have been, but no damaged floor tile.
— F. Okoro, Crane, TX
Common Questions
Pipe Repair Questions We Answer Every Day
A slow pinhole leak inside a wall can run for months before surface damage appears. By the time you see a stain, the moisture intrusion is typically already significant. If your meter shows movement with everything off, call us — we can pressure-test and locate it before it becomes a major remediation project.
In most cases, the pipe itself needs to be physically accessed to make a durable repair — but the amount of wall we open depends entirely on how precisely we can locate the failure first. With acoustic detection and thermal imaging, we typically open a single, small access point rather than a wide section of wall.
Repair options include direct slab access (jackhammer to the pipe, repair, patch), rerouting the supply line above slab through framing, and for copper systems with multiple pinhole failures, epoxy pipe lining from inside the pipe without excavation. We use acoustic and thermal detection to locate the leak before recommending a repair approach.
Galvanized pipe corrodes from the interior outward — by the time one section fails, the rest of the pipe is in varying stages of the same process. A localized repair buys time, but another section typically fails within 1–3 years if the system is at end of life. The honest answer is: it depends on how far along the corrosion is and how many sections are already narrowed or showing surface rust.
A single localized pipe repair — finding and fixing one failure point — typically takes 1.5–3 hours including detection, access, repair, and pressure testing. Slab leak reroutes run 3–5 hours depending on the routing path and pipe length. A full-house repipe is a multi-day project — typically 2–4 days for a standard single-family home depending on size and pipe count.
For slab access openings, we clean up concrete debris, complete the pipe repair, and patch the concrete. Tile or flooring restoration over a slab patch is normally a separate trade.
Service Area
Pipe Repair Covering Crane and All of Crane, TX
Masters Plumbing Service dispatches pipe repair technicians throughout Crane and the broader Crane, TX service area. Same-day service is available on most calls. Emergency burst pipe response is available 24 hours a day.
